活化改性半焦用于烟气脱硫催化剂制备工艺优化

为研究不同制备工艺条件下的烟气脱硫催化剂吸附去除烟气中硫化物的性能,采用硝酸活化的半焦脱硫剂,通过穿透时间和硫容评价所制备催化剂的脱硫性能.采用固定床反应器考察了催化剂表面基团酸碱性、催化剂成型的制备顺序、黏结剂和催化剂尺寸及负载金属氧化物等制备工艺条件对催化剂脱硫性能的影响.结果表明:原料半焦表面呈碱性,半焦经硝酸氧化改性后,表面呈酸性,高温煅烧可以使半焦表面酸性官能团分解成碱性官能团,催化剂表面净碱量越大,脱硫性能越好;采取先将半焦成型再进行高温煅烧、水气活化的工艺,脱硫活性更高;最适合的黏结剂为煤焦油;最佳的催化剂粒径为3mm;烟气中通入O2能显著提高半焦吸附催化剂的脱硫性能,O2体积分数以5％为宜,烟气中适量H2O是脱硫必不可少的条件,水汽体积分数以8％最佳;在催化剂制备过程中添加质量分数为1％的V2O5,可以明显改善催化剂的脱硫性能.     

污泥热化学处理研究进展

由于传统污泥处置技术存在局限性,污泥热化学处理技术更具有应用前景。综述了近几年国内外污泥热化学处理技术的研究进展,在此基础上介绍了污泥热解、污泥气化及污泥超临界水气化3种污泥处理技术,归纳了温度、升温速率、催化剂等因素对3种污泥热化学处理技术污泥处置后产物特性、尤其是富氢气体产物的影响规律,简明阐述了不同污泥热化学处理方式的特点,对比了3种热化学处理方法的差异。还介绍了污泥热解、气化技术的工业实例和一般工艺流程,分析了不同处置技术存在的问题,对今后污泥高效利用提出了建议。     

构造煤孔隙结构与瓦斯耦合特性研究

利用压汞法、低温氮吸附法、瓦斯等温吸附和解吸试验对平煤八矿构造煤和共生原生结构煤进行综合分析,探讨了构造煤孔隙结构与瓦斯耦合特性.结果表明,构造煤以微孔为主,中孔和大孔相对发育且含较多细颈瓶孔,孔隙连通性差.与共生原生结构煤相比,构造煤各孔径阶段的孔容和孔比表面积都有所增加.构造煤比表面积的增加具有阶段性,即孔径＜ 1.2 nm时为慢增加阶段,孔径=1.2 ～ 4.9nm时为快增加阶段,孔径＞4.9 nm时为稳定阶段.构造煤极限瓦斯吸附量a的增大与比表面积快增加阶段关系密切,但小于其BET比表面积的增幅.瓦斯解吸初期0～2 min内构造煤瓦斯解吸速度和解吸量明显大于共生原生结构煤,与中孔和大孔的变化一致,2 min以后瓦斯解吸迅速衰减.低煤体强度、高瓦斯含量的构造煤以气-煤共溶体形式储集更多弹性潜能,突然卸压时瓦斯膨胀能迅速释放,煤层中发育的构造煤增加了煤与瓦斯突出的危险性.     

管道内瓦斯爆炸温度与压力峰值试验研究

为分析瓦斯爆炸的火焰温度及压力峰值在管道中的传播规律,采用瓦斯管网爆炸测试系统进行试验,通过爆炸压力和爆炸火焰温度采集系统采集数据。在相同点火能量和点火位置的条件下,分析了体积分数对瓦斯爆炸的温度峰值和压力峰值的影响,及温度峰值和压力峰值随管道距离的变化规律。结果表明:当瓦斯体积分数低于9.5%时,温度峰值和压力峰值随瓦斯体积分数增大而增大;同一体积分数下,温度峰值最大值出现在最接近爆源的位置,并呈逐渐下降的趋势,接近爆源的温度峰值下降较明显,随管道延长,温度峰值的下降减慢且趋于平缓;温度峰值与传播距离近似呈三次函数关系;冲击波压力峰值随管道传播呈先上升后下降再上升的波动性变化。     

落石冲击作用下架设油气管道响应分析

针对影响油气管道安全运营的落石冲击问题,基于弹塑性力学、Cowper-Symonds本构模型和有限元方法,建立了球形落石冲击油气管道的计算模型,对管道动态响应过程进行了数值模拟。对冲击速度、落石半径、管道内压力和落石冲击位置进行了参数敏感性分析,研究了各参数对管道冲击变形的影响规律。结果表明:落石的冲击能量主要用于管道塑性变形;冲击过程中,落石与管道的接触区域由初始的椭圆斑逐渐变成了椭圆环;管道塑性变形随着冲击速度和落石半径的增大而增大,随内压和落石偏移度的增大而减小。该研究工作为油气管道的安全评价及防护工程的设计提供了参考依据,对保障油气安全运输具有重要的工程意义。     

Methane and nitrous oxide emissions from a subtropical coastal embayment (Moreton Bay, Australia)

Surface water methane (CH₄) and nitrous oxide (N₂O) concentrations and fluxes were investigated in two subtropical coastal embayments (Bramble Bay and Deception Bay, which are part of the greater Moreton Bay, Australia). Measurements were done at 23 stations in seven campaigns covering different seasons during 2010-2012. Water-air fluxes were estimated using the Thin Boundary Layer approach with a combination of wind and currents-based models for the estimation of the gas transfer velocities. The two bays were strong sources of both CH₄ and N₂O with no significant differences in the degree of saturation of both gases between them during all measurement campaigns. Both CH₄ and N₂O concentrations had strong temporal but minimal spatial variability in both bays. During the seven seasons, CH₄ varied between 500% and 4000% saturation while N₂O varied between 128 and 255% in the two bays. Average seasonal CH₄ fluxes for the two bays varied between 0.5 ± 0.2 and 6.0 ± 1.5 mg CH₄/(m²·day) while N₂O varied between 0.4 ± 0.1 and 1.6 ± 0.6 mg N₂O/(m²·day). Weighted emissions (t CO₂-e) were 63%-90% N₂O dominated implying that a reduction in N₂O inputs and/or nitrogen availability in the bays may significantly reduce the bays' greenhouse gas (GHG) budget. Emissions data for tropical and subtropical systems is still scarce. This work found subtropical bays to be significant aquatic sources of both CH₄ and N₂O and puts the estimated fluxes into the global context with measurements done from other climatic regions.     

Metal concentrations in used engine oils: Relevance to site assessments of soils

Used engine oils contain metals, which upon entering soils may pose risks to human health or the environment. In this study, previously published concentrations of 23 metals in 213 used engine oil samples from the early 1970s to the mid-1990s are statistically evaluated. Neat (100%) used engine oils were found to contain relatively high concentrations of lead, calcium, and zinc, attributable to piston blow-by of leaded gasoline, calcium salt detergent additives, and zinc-bearing anti-corrosion/anti-oxidation additives, respectively. Wear metal concentrations were lower. The lead concentration in used engine oils in the U.S. declined between the 1970s and early 1990s, potentially providing a basis to constrain the “age” of used engine oil(s) in soils. The concentrations of 23 metals in used engine oils were compared to soil risk benchmarks in 15 representative jurisdictions in the U.S., Canada, Australia, and Europe. The maximum concentrations in neat (100%) used engine oil of eight metals – Be, Co, Fe, Mn, Ni, Se, Ag, and Ti – were lower than their collective minimum benchmarks in soils for the jurisdictions surveyed, indicating their concentrations in soils could not be reasonably expected to exceed any soil benchmarks. Nine metals (As, Ba, Cd, Cr, Cu, Pb, Sn, V and Zn), but particularly arsenic, cadmium, lead, tin, and zinc, were identified as potential contaminants of concern (PCOC) for soils from locations impacted with used engine oils, owing to their higher median concentrations (i.e., 2.5, 1.4, 1038, 5.0, and 922 mg/kg in oil, respectively) relative to most soil benchmarks. Site-specific benchmarks and metal concentrations at reasonable oil in soil concentrations require consideration when developing the suite of PCOC metal analytes for conducting site assessments of soils impacted by used engine oil.     

分段变速加载对含瓦斯突出煤力学特性影响试验研究

为探究采动应力变化对含瓦斯突出煤力学特性的影响，利用RLW-500G煤岩三轴蠕变-渗流试验系统，对新景矿含瓦斯突出煤进行了不同围压和瓦斯压力下的常规三轴和分段变速加载力学试验。结果表明:煤样在2种应力路径下的全应力应变曲线均可分为压密、线弹性、塑性变形、应力跌落和残余应力5个阶段；随着围压的升高或者瓦斯压力的降低，煤体在2种应力路径下的强度和弹性模量均增大；相较于常规三轴，煤体在分段变速加载路径下的强度普遍增大，峰值轴向应变、峰值环向应变绝对值和峰值体积应变绝对值也普遍增大，失稳破坏瞬间应力跌落和能量释放更加剧烈。Mohr-Coulomb强度准则仍然适用于分段变速加载条件下的含瓦斯突出煤，该研究对于认识煤与瓦斯突出的发生机制具有一定的指导意义。     

城市燃气事故生命损失风险可接受标准研究

为提高我国城市燃气风险管理水平，帮助风险管理者科学地分配维护资源，探讨提出了我国城市燃气事故生命损失风险可接受标准；采用AIR指标法确定了个人风险可接受标准范围为(2.397 3×10-7,4.794 7×10-7)；运用F-N曲线法结合ALARP原则，确定了社会风险可接受标准，最大可接受风险的截距为4.794 7×10-7，可忽略风险的截距为4.794 7×10-8；利用生活质量指数推导模型，计算了达到城市燃气事故可忽略风险水平的最优安全投入成本；基于风险动态原则，分析提出了风险可接受标准的更新办法。研究结果表明:我国城市燃气行业可接受风险水平低于煤矿、大坝、化工等危险行业的可接受风险水平；虽然我国城市燃气事故死亡率逐年降低，但要达到可忽略的风险水平，每年还需大量安全资金投入。     

基于数字信息化的消防呼吸气瓶检验管理系统研究与开发

为解决碳纤维缠绕式消防呼吸气瓶检验中因单机作业而存在的检验效率低、检验质量差、受人为因素影响的问题，研究开发基于数字信息化的碳纤维缠绕式消防呼吸气瓶检验管理系统，该检验系统包括消防呼吸气瓶数据库、OA系统、呼吸气瓶检验软件和手机APP。利用二维码技术和计算机网络，实现呼吸气瓶数据库、检验软件、OA约检和报告审核审批系统、手机APP的数据传输。结果表明:该检验管理系统实现了呼吸气瓶检验的无纸化、过程的可追溯性、检验结果的防伪性等功能，其对于碳纤维缠绕式消防呼吸气瓶检验具有较强的适用性和可行性。